Project goal:
The owner of a new house area 100 M² I immediately searched for an economical and effective solution for heating, After all, the costs of electric boiler or gas boiler were too high. Given the sole floor system and the absence of additional heat sources, The choice stopped on the heat pump Air-Wood Raymer Ray-10DS2-EVI power 10 kW. It provides stable and economical heating even at low temperatures, and the installed relay helps optimize the operation of the system. After some time, it is planned to add solar panels, which will reduce electricity costs even more.
Why the choice fell precisely the heat pump Raymer Ray-10DS2-EVI?
The selection of the heat pump Raymer Ray-10DS2-EVI was due to several key factors:
Energy efficiency and savings
The heat pump consumes significantly less electricity compared to the electric boiler, providing stable heating at the same time. COP (Energy transformation coefficient) This model has high, which allows you to get more heat with less energy consumption. For this model, thermal efficiency is equal 4,9 kW, What does 1 kW of electricity consumption. The pump is capable of producing almost 5 kW of heat.
Compatibility with a warm floor system
The house is fully equipped with a water warm floor, ideally combined with a low -temperature heating system, that Raymer Ray-10DS2-EVI provides. This allows you to achieve maximum efficiency at minimal costs.
Stable work at low temperatures
Thanks to EVI technology (Injection of a pair of refrigerant), This heat pump effectively works even at -30 ° C, which is critical for the climatic conditions of Ukraine.
Readiness for integration with alternative energy sources
The owner of the house plans to install solar panels, And the heat pump can work in combination with renewable (renewable energy sources), which will further reduce heating costs.
Durability and minimum maintenance
Raymer Ray-10DS2-EVI is supportive equipment, not requiring frequent intervention. Thanks to high -quality components and hermetic design, it has a long service life.
Thus, This heat pump was the best choice for an autonomous, economical and efficient heating of the house.
Stages of work
1. Outdoor unit installation
The outer block of the heat pump was temporarily installed on a cement podium, so that there is no obstacle to facade work. Later, the block will be installed on a special stand and placed near the facade wall of the house.
The block is placed outdoors to ensure effective heat transfer with the environment. Outdoor installation allows the Raymer Ray-10DS2-EVI to use the outer air energy for heating the house to heating the house. Air free access provides a stable flow of air and prevents the formation of ice on the heat exchanger.
In this case, the external protection of the block is not provided, since the thermal pump body is designed for outdoor operation and is made of durable materials and coatings, not subject to corrosion.
The freon highway is mounted with all the rules of the manufacturer: The minimum allowed length for minimizing heat loss, rubber insulation from damage and severe icing.
2. Installation of the indoor unit.
The installation of a heat pump hydraulic pump provides for installation in the technical room, where sufficient space for maintenance and connecting all communications is provided. The unit is installed on a flat surface and is fixed to minimize vibrations during operation.
The connection of the hydraulic engine is made using thermal insulated pipelines, which connect it with a tank-drive and a warm floor system. The input and output for the coolant are equipped with shut -off valves, which allows service without the need to drain the entire system. The lines provide for the installation of temperature sensors and a duct relay to control the work.
The hydraulic engine is also connected to the mains in accordance with the requirements of the manufacturer, taking into account separate automatic protection and voltage relay. A built -in controller is used to manage the operation of the system, allows you to configure the heating modes and control the current parameters.
After the installation was completed, the tightness of the joints was checked, filling the system with a coolant and its test launch. The hydraulic engine automatically adjusts the water temperature, Providing stable operation of the heat pump and the effective distribution of heat in the heating system.
3. Installation of storage tank.
Storage tank for 60 liters connected to the comb warm floor, ensuring the effective distribution of heat throughout the system. Hot heat carrier from a hydraulic engine first gets into the tank, which plays the role of buffer capacity, Stabilizing the temperature and pressure. Next, the heated water enters the supplier, where is evenly distributed through individual circuits of the warm floor.
After circulation in the floor pipelines, the cooled coolant returns to the reverse comb, and from there-back to the boiler tank. Here it is heated again and is submitted to the system, Supporting continuous heating of the room. Due to this scheme, the number of heat pump compressor launches is reduced, which increases its effectiveness and extends the resource of work.
Automation controls the temperature of water in the tank and comb, and the circulation pump provides an uniform flow of the coolant. Additionally installed shut -off valves, Finding valves and temperature sensors, which guarantee the safe and stable operation of the entire system. This approach provides a comfortable microclimate in the house, uniform distribution of heat without overheating and cold, as well as electricity savings due to the optimized operation of the heat pump.
4. Installation of voltage stabilizer
A voltage stabilizer is installed in this project Elex Hertz y 16-1/40 v3.0, which provides stable power supply for all equipment. The main function of the stabilizer is the protection of the heat pump, hydraulic engine and other electrical appliances from voltage drops in the network.
The device automatically levels the voltage, preventing overload and possible damage to the system. Due to this, uninterrupted operation of heating equipment is ensured, its reliability is increased and the life of operation is extended.
The stabilizer is mounted on the wall next to the hydraulic engine, which ensures the compactness of placement and convenient access for maintenance.
4. Auxiliary system components: security group and explitor
For the correct and safe operation of the heat pump of the heat pump, auxiliary components play an important role, among which the security group and expansion tank.
The security group is installed on the heat carrier supply line and includes a safety valve, Manometer and automatic air vent. The safety valve protects the system from excess pressure, dropping excess heat carrier in case of exceeding the set value. The manometer makes it possible to control the working pressure in the system, And the air vent automatically produces air traffic jams, which can form during work.
The expansion tank compensates the temperature expansion of the coolant, preventing sharp pressure drops. It connects to the reverse line of the heating system, ensuring stable operation of a hydraulic engine and the entire warm floor system. The volume of the tank is selected in accordance with the calculation parameters of the system, to effectively take an excess of the coolant during heating and return it when cooling.
These components work in the complex, Providing uninterrupted, Effective and safe operation of the entire heating system.
After installing the heat pump, the Raymer Ray-10DS2-EVI client receives:
Energy efficient and economical heating: A heat pump uses air energy to heat a room and heat water, reducing electricity costs to 75% compared to traditional systems.
Stable work at low temperatures: Thanks to EVI technology (Enhanced Vapor Injection) The heat pump works effectively even at temperatures up to -25 ° C, Providing comfortable heat in the cold season.
Automation and convenient control: Intelligent control system allows you to configure operating modes via the display or remotely (If there is a Wi-Fi module), which simplifies control over the operation of the device.
Low operating costs: Using a heat pump significantly reduces your electricity and gas bills, making it a profitable investment for many years.
Environmental friendliness: The device operates on the ecological refrigerant R32, does not produce harmful emissions and contributes to the preservation of the environment.
Durability and reliability: High -quality materials, A reliable compressor and a freezing protection system provide a long -term service for thermal pump for a long time.
Versatility of use: Suitable for heating private houses, commercial premises, hotels and other objects, as well as to work with radiators, Fancoals and warm floor.
Having installed Raymer RAY-10DS2-EVI, You get warm, Comfort and savings without unnecessary troubles!
